If your unit displays a red light bar with partial white flashing, this indicates that the unit did not detect the globe position during its previous cycle.
Visit for solutions if your Litter-Robot 4 has a red light bar with a partial white flashing globe. Get instant support and fixes today.
Check and clear any obstructions in the waste port. Waste clumps or toys could obstruct the globe rotation and cause a globe position or over-torque fault.
Find solutions for your Litter-Robot 3's three lights flashing position sensors issue. Fix issues with your Connect Upgrade Kit today!
22 apr 2024 · 1- If you are using a generic power adapter causing the motor to fail during the cycle or cycle slower than the usual. 2- If the magnets of the ...
Recently our Litter Robot III LR3C-1200-CE (SN LR3CI359573) shows a home position fault. The globe stops at the end of the cycle just before it returns to its home position. Suggestions I found on the web didn’t help. It is using the official adapter and it is directly plugged in the wall socket. Up till now I just turn off the robot, reposition the globe by hand and turn it on again. It will cycle and will work for a while as expected until it doesn’t. Rinse and repeat. I don’t think the motor ...
10 feb 2021 · The Hall Effect Sensor is the sensor responsible for the tracking of the globe's position. It's what makes your Litter-Robot so intelligent.
Hi! We got a Litter Robot 3 about 6 months ago. Yesterday it showed a Home Position Fault (all lights blinking sequentially from red to blue). I can’t seem to find anything online that deals with this precise issue. Would anyone have any suggestion? Thank you so much in advance for your help!
While cycling, if a potential condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly ( ...
Find easy steps on replacing the pinch detect terminals of your Litter-Robot 3. Visit now for a quick and smooth fix to enhance your product's efficiency.
If your unit's light bar is red with two flashing white lights, this indicates that the unit cannot detect the Globe position. Learn more. Red with flashing ...
Discover solutions for all Litter-Robot 4 light codes in our comprehensive guide. Find quick fixes and get your Litter-Robot working perfectly again. Click now!
If the lights on the control panel blink, right to left, left to right or together, the problem is still the same: the robot has failed to track the position of ...
Most of you are here because there are 3 flashing lights on your Litter-Robot's control panel. Sometimes this problem is caused by a faulty power supply or the motor itself. If even after checking the set screw on the motor and checking the voltage on the power supply with a multimeter, the lights…
Short press the Reset button, then short press the Cycle button to run a Clean cycle. After your Litter-Robot cycles, it should return to the Home position, displaying a blue light bar.
Make sure bluetooth is enabled. Accept Location Services if prompted. If the app is unable to find Litter-Robot via your device's bluetooth, move your mobile device closer to your Litter-Robot, check that your mobile device's bluetooth is turned on, and the power button on your Litter-Robot is blue.
Litter-Robot comes equipped with current-sensing capability to detect if the motor is connected and running properly. If the unit displays a blue and white alternating light bar, there is an issue with the motor connection, which affects the rotation of the globe.
To reconnect your unit, re-enable the connection by pressing the Connect button once to turn the WIFI off, indicated by a white Connect LED.Then, press the Connect button a 2nd time to reestablish the connection. The Connect LED will begin flashing blue again but should change to solid blue after a few seconds.
Litter-Robot is equipped with anti-pinch sensors on both sides of the waste drawer chute to ensure your cat's safety while in use. These sensors monitor for potential pinch conditions at all times. If your unit displays a green and white alternating light bar, this indicates an anti-pinch fault during power up.
Clean the globe with Litter-Robot Cleaner Spray or Cleaner Wipes, or with water and a mild soap. There are no electronic components in the globe that can be damaged by soap and water. If the globe has become extremely dirty, it can be soaked and cleaned with a water hose.
Using more than 10 lbs of litter can strain the motor, causing an over torque fault. Make sure the litter is just below the raised fill line. Some brands of litter are heavier than others. For these litters, we recommend keeping the litter at least a half inch below the fill line to avoid weight-related errors.
Litter-Robot comes equipped with current-sensing capability to detect if the motor is connected and running properly. If the unit displays a blue and white alternating light bar, there is an issue with the motor connection, which affects the rotation of the globe.
Introduction: My name is Aron Pacocha, I am a happy, tasty, innocent, proud, talented, courageous, magnificent person who loves writing and wants to share my knowledge and understanding with you.
We notice you're using an ad blocker
Without advertising income, we can't keep making this site awesome for you.